Avalon 900 Ps Pellet Stove
But he did not check the cap. This was less than a month ago. And the problems happen when it is at or below freezing. Otherwise we have a poor (Some smoke still comes out when loading) but atleast acceptable fire. This is a new stove. However the flue install was for a pellet stove (don't know what type) that the previous homeowners used. Travis Industries, manufacturer of the Avalon AGP pellet stove, refuses to sell any replacement parts on line. While cleaning our stove as part of regular maintenance, my husband accidentally tore the fragile aluminum foil flex hose on the outside air intake. The Avalon Astoria pellet stove is a medium sized stove with a huge capacity hopper at 115 pounds. At its lowest feed rate, the Astoria is rated for up to a 68 hour burn time.
- Many pellet stove problems are due to poor quality pellets. Burning high quality pellets on-sight often convinces the pellet heater owner to switch to a higher quality fuel. ELIMINATING 'FALSE FIXES' AND MAKING CORRECT DIAGNOSIS Often a part is switched out, improving the stove’s performance enough to overcome the true problem.
- Lopi and Avalon Pellet Stove - Barbed Brass Nipple for Draft Tubing #250-00379 This Brass Nipple screws into the side or back side of the combustion housing on most Avalon and Lopi Pellet Stoves $20.20. Add to Cart Compare. Knob for Fan Speed Control. Knob for Fan Speed Control / Rheostat Waterford 904-569 Regency 904-569 Enviro EG-95067.
Avalon Pellet Stove PartsPellet Stove Parts 4 Less has one goal, to make sure that you can get all the pellet stove parts you need from one location. That includes for your Avalon Pellet Stove. We carry a wide selection of replacement and aftermarket parts that are specific to your unit, including: Gaskets in a variety of sizes and styles, Temperature sensors, Limit switches, Control boards, Igniters, Motors, Blowers.
Repair & upgrade your Avalon stove with our full line of Avalon pellet stove parts. Avalon and Lopi Convection Blower Astoria, Yankee Bay, Leyden.
Unfortunately, once the current inventory is depleted we will no longer be able to carry these parts.
Pellet stove problems are infrequent, but pellet stoves being mechanical devices, can develop faults. The main cause of difficulties when using a pellet stove is lack of regular and thorough cleaning. Cleaning procedures are essential to avoid a build up of ash which can undermine the efficiency of your stove. (See links at the bottom of the page).Many modern stoves have digital circuit boards on which LED's glow in certain combinations to diagnose pellet stove problems. For an explanation of what these lights mean, you will need the manual for your stove.When servicing a pellet stove, make sure that the unit is unplugged from the electricity supply if there is any chance of coming into contact with electrical parts.
If the unit needs an electrical supply to be re-connected to test a component, be very very careful.Before venturing inside your stove's workings, a good idea is to give it a clean up. This will make the job a lot less messy and reduce the likelihood of small parts being mislaid.
When working on the stove, spread a drop cloth around the working area to prevent fly ash getting into floor coverings.If the Stove Doesn't StartFirst, check the fundamentals. Is there power to the stove, and are there pellets. Check power to the stove by plugging another appliance, such as a portable, lamp into the socket that the stove takes power from. Check the level of pellets in the hopper.Occasionally, a pellet stove problem can be pellets bridging over the hopper outlet and prevent themselves from dropping to the auger. If you suspect that this might be what's happened, disconnect the power supply and empty the hopper gently until you get to the bottom. This problem can be caused by over long pellets, or friction with the hopper sides.
Avalon Astoria Exhaust Blower
Avalon Astoria Pellet Stove Problems
If pellets won't slide, a light spray over the inside of the hopper with silicon lubricant will help.With the hopper empty, it's usually possible to see the auger. Switch the power back on, start the stove, and see whether or not the auger is turning.
If a slight movement only can be seen, the probability is that it's jammed either by fines, (pellet dust), or a foreign body. Listen for the auger motor to check whether or not it's working.Some stoves have a switch on the hopper lid to stop the stove if the hopper is open. This will need to be depressed to view the auger operation.
Auger gear motors are very powerful and on no account should fingers come anywhere near a moving auger.The igniter may be faulty. In normal operation, they can usually be seen to glow red on start up. If you have a faulty igniter, it's possible to start most stoves by using a handful of pellets in the burn pot and lighting them with starter gel. Thermostat on/off operation will not be possible until a new igniter is fitted.The next step is to get out the manual or download one online, (they are available on the home website of nearly all manufacturers), and find where the stove's internal fuses are,take them out and check them using a continuity checker.Pellets Not Getting to the Burn Pot?You've checked the hopper and the auger as above? If the stove has run out of fuel, it will take a few minutes for the empty auger to fill and start delivering fuel to the burn pot.If the auger is jammed with fines, (dust from the pellets), it might be possible to free it by working from both ends with a screwdriver, wire rope, and a vacuum cleaner.
Stove power off for this operation. If a foreign body such as a woodscrew has got in there, the auger will need to be dismantled to clear it. Instructions in the manualSome stoves have 'snap switches' which turn off the auger if the stove should become overheated. Check to see if these need re-setting or are faulty.Pellet Stove Troubleshooting: Dark and Sooty Flame?For one reason or another, not enough air is getting to the fire. The most common cause of this type of pellet stove problem is a clinkered up burn pot which can be because of inadequate maintenance or poor pellet quality.Take the burn pot out and give it a thorough cleaning.
Scrape off the clinkers using the tool provided with the stove, or an old screwdriver. Make sure that all the air holes are clear. A portable drill can help with this, but get a drill bit the right size or slightly smaller. You do not want to enlarge the holes.Next, have a look at both the inlet and the outlet venting, including exhaust vents within the stove itself.The air intake, if from outside, should have a mesh cover to stop leaves and other debris, as well as small animals from entering. Check that the intake is clear.Stoves have exhaust channels within the stove body which can fill with fly ash. Check your manual for instructions on cleaning these. The flue system can also have a build up of fly ash, particularly at elbows.
Sometimes the rain cap can become clogged.Pellet stove combustion is powered by air blown from the combustion blower.
Lifespan of Pellet Stove Igniters
Pellet Stove Igniters are a tricky group of products. I say this because they are not all built the same and they can be unpredictable in how long they last with a few exceptions. The Pellet Stove Igniter used by Quadrafire pellet stoves fails the most frequently of any pellet stove igniter I know of. […]